Maytag Centennial Washer Stuck on Sensing?

Maytag Centennial Washer Stuck on Sensing? Quick Fix!

As a Maytag Centennial washer owner, I've found myself frustrated when the machine is stuck on the sensing cycle, refusing to budge. It's more than an inconvenience; it's a potential disruption to my daily routine, leaving me with dirty laundry and no immediate solution. It seems to occur when the load is unbalanced or too heavy, with the machine unable to determine the weight and needed water quantity. However, thanks to my knack for troubleshooting, I've learned to manage this pesky issue.

Key Takeaways:

  1. Maytag Centennial washers often get stuck on sensing due to an unbalanced or overloaded laundry, defective parts, or technical issues.
  2. Resetting the machine, running a self-diagnosis, or addressing specific component issues like faulty capacitors or actuator can help resolve the problem.
  3. Prevention is often as simple as ensuring proper load balance and avoiding overloading.

A washer stuck in the sensing phase may seem like a small issue. But as you'll see in this article, it has larger implications and easy resolutions worth understanding.

'Sensing' Stage in a Maytag Centennial Washer

The 'sensing' stage in a Maytag Centennial washer is an essential part of the wash cycle. During this phase, the washer determines the weight of the load and calculates the appropriate amount of water needed. It ensures that the washer doesn't waste water by using more than necessary or leave your clothes inadequately cleaned by using too little.

However, there are instances when the washer gets stuck on the 'sensing' stage, causing frustration and inconvenience. This can occur due to various reasons, such as an unbalanced or heavy load, malfunctioning components, or clogged parts. In the following sections, we will delve into these issues and provide you with step-by-step instructions on how to troubleshoot and fix them.

Resetting the Washer

Before diving into troubleshooting the 'sensing' issue, it's worth trying a simple reset of the washer. Sometimes, a quick reset can resolve minor glitches and get your washer back on track. Here's how you can reset your Maytag Centennial washer:

  1. Unplug the washer from the power outlet.
  2. Wait for approximately one minute.
  3. Plug the washer back in.

By performing this reset, you are essentially giving the washer a fresh start. It can help clear any temporary issues that might have caused the 'sensing' problem. If the issue persists after the reset, don't worry. There are additional troubleshooting steps you can take to identify and fix the underlying cause.

Initiating Maytag Self-Diagnosis Feature

Maytag Centennial washers come equipped with a self-diagnosis feature that can help identify the cause of the 'sensing' issue. By running a self-diagnosis, you can retrieve error codes that indicate specific problems with the washer. Here's how you can initiate the self-diagnosis feature:

  1. Ensure that the washer is plugged in and powered on.
  2. Press and hold the 'Start' button for three seconds.
  3. Release the 'Start' button and wait for the self-diagnosis to begin.

During the self-diagnosis, the washer will go through a series of tests and display error codes if any issues are detected. These error codes can provide valuable information about the components or systems that are malfunctioning. Once you have the error codes, you can refer to the washer's manual or consult online resources to understand what they mean and how to resolve them.

How to Remove Any Present Error Codes

If your Maytag Centennial washer displays error codes during the self-diagnosis, it's important to clear them before proceeding with troubleshooting. Clearing the error codes ensures that you are starting with a clean slate and allows you to accurately monitor the washer's performance after implementing any fixes. Here's how you can remove the error codes:

  1. Unplug the washer from the power outlet.
  2. Wait for approximately 15 seconds.
  3. Press and hold the 'Start/Cancel' button for five seconds.
  4. Release the 'Start/Cancel' button.

Now you are ready to move on to identifying the specific reasons why your washer is constantly stuck in the 'sensing' stage.

Finding Out Why Your Washer Is Constantly Sensing

If your Maytag Centennial washer is consistently getting stuck in the 'sensing' stage, there may be several potential causes. Let's explore some of the common culprits and the steps you can take to resolve them.

1. Damaged Capacitor

A damaged capacitor is one possible reason why your washer is stuck on the 'sensing' stage. The capacitor is responsible for providing the necessary power to various components of the washer. If it is defective or burnt out, it can cause the washer to malfunction. To replace the capacitor, follow these steps:

  1. Unplug the washer and ensure that it is not connected to a power source.
  2. Locate the control panel at the top of the washer.
  3. Remove the screws securing the control panel and lift it up to access the control board.
  4. Inspect the control board for any burnt or damaged capacitors.
  5. If you identify a faulty capacitor, take note of its specifications.
  6. Order a replacement capacitor that matches the specifications.
  7. Once you have the replacement capacitor, carefully desolder the faulty capacitor from the control board.
  8. Install the new capacitor by soldering it onto the control board, ensuring proper polarity.
  9. Reassemble the control panel and secure it with the screws.

2. Malfunctioning Washer Actuator

Another possible cause of your Maytag Centennial washer being stuck on the 'sensing' stage is a malfunctioning washer actuator. The actuator is responsible for shifting the washer between different cycles. If it is defective, it may fail to change positions, causing the washer to remain in the 'sensing' stage. To replace the actuator, follow these steps:

  1. Unplug the washer and ensure that it is not connected to a power source.
  2. Remove the back panel of the washer to access the actuator.
  3. Locate the actuator, which is typically positioned near the motor.
  4. Disconnect the wiring harness from the actuator.
  5. Remove any screws or bolts securing the actuator in place.
  6. Take note of the actuator's specifications and order a replacement.
  7. Install the new actuator by reversing the steps above.
  8. Once the actuator is securely in place, reattach the wiring harness.
  9. Replace the back panel of the washer.

3. Obstructed Drain Pump

A clogged or obstructed drain pump can also cause your washer to stay stuck in the 'sensing' stage. If the drain pump is unable to remove the water from the washer, it can prevent the wash cycle from starting. To clean the drain pump, follow these steps:

  1. Unplug the washer and ensure that it is not connected to a power source.
  2. Locate the drain pump, which is typically located at the bottom of the washer.
  3. Place a towel or bucket underneath the pump to catch any water that may spill.
  4. Disconnect the hoses connected to the drain pump, taking note of their positions.
  5. Inspect the drain pump for any debris or blockages.
  6. Remove any debris or blockages using a small brush or cloth.
  7. Reattach the hoses to the drain pump, ensuring they are securely connected.
  8. Plug the washer back in and test whether the 'sensing' issue is resolved.

4. Unusable Lid Switch

A broken or malfunctioning lid switch can also be the reason why your washer is stuck on the 'sensing' stage. The lid switch is responsible for detecting whether the washer's lid is closed before starting the wash cycle. If the switch is defective, it may prevent the washer from advancing beyond the 'sensing' stage. To switch out the lid switch, follow these steps:

  1. Unplug the washer and ensure that it is not connected to a power source.
  2. Locate the lid switch, which is typically positioned near the top of the washer.
  3. Disconnect the power supply and water hoses from the washer.
  4. Remove the control panel by removing the screws securing it.
  5. Disconnect the wiring harness from the lid switch.
  6. Remove any screws or bolts securing the lid switch in place.
  7. Take note of the lid switch's specifications and order a replacement.
  8. Install the new lid switch by reversing the steps above.
  9. Once the lid switch is securely in place, reattach the wiring harness.
  10. Replace the control panel and secure it with the screws.
  11. Reconnect the power supply and water hoses.

5. Inefficient Water Inlet Valve

Lastly, an inefficient water inlet valve can also contribute to your washer being stuck on the 'sensing' stage. The water inlet valve is responsible for controlling the flow of water into the washer. If it is defective, it may prevent the washer from achieving the necessary water level, causing it to remain in the 'sensing' stage. To set up a new water inlet valve, it is recommended to consult the owner's manual or seek professional help, as the process can vary depending on the specific model of your Maytag Centennial washer.

FAQ Section

How do you reset the sensor on a Maytag Centennial washing machine?

To reset the sensor on a Maytag Centennial washing machine, you can try the following steps:

  1. Unplug the washer from the power outlet.
  2. Wait for approximately one minute.
  3. Plug the washer back in.

What to do if washer is stuck on sensing?

If your washer is stuck on the 'sensing' stage, there are several steps you can take to resolve the issue:

  1. Rebalance the load: Ensure that the load inside the washer is evenly distributed. An unbalanced load can cause the washer to stay stuck in the 'sensing' stage.
  2. Try smaller loads: If you consistently experience the 'sensing' issue, try reducing the size of your loads. Overloading the washer can also contribute to the problem.
  3. Reset the washer: Unplug the washer from the power outlet, wait for a minute, and then plug it back in. This can help clear any temporary issues that may be causing the 'sensing' problem.
  4. Run self-diagnostics: Initiate the self-diagnosis feature on your Maytag Centennial washer to identify the specific problem. Retrieve any error codes and refer to the washer's manual or online resources to understand how to resolve them.

What does sensing mean on a Maytag washer?

When a Maytag washer displays 'sensing' on its control panel, it means that the washer is in the initial stage of the wash cycle. During this stage, the washer determines the weight of the load and calculates the appropriate amount of water needed. It ensures that the washer uses the correct water level for optimal cleaning performance.

Why is the sensing light on my Maytag Centennial washer lid lock flashing?

If the sensing light on your Maytag Centennial washer lid lock is flashing, it may indicate a problem with the lid lock mechanism. The flashing light is a visual indication that the washer is unable to detect whether the lid is properly closed. This can prevent the washer from progressing beyond the 'sensing' stage. In such cases, it is recommended to check the lid lock mechanism for any obstructions or defects and replace it if necessary.

0 0 votes
Article Rating
Subscribe
Notify of
guest
0 Comments
Inline Feedbacks
View all comments