Is Your Maytag Bravos Washer Stuck on Sensing? 11 Fixes

Are you experiencing the frustrating issue of your Maytag Bravos washer getting stuck on the sensing mode and not moving on to the wash cycle?

Don't worry, you're not alone.

Many Maytag Bravos washer owners have encountered this problem, but luckily, there are steps you can take to troubleshoot and resolve the issue before contacting a technician.

In this article, we will explore the basics of why your Maytag Bravos washer is stuck on sensing and provide you with further troubleshooting methods to help get your washer back up and running smoothly.

Key Takeaways:

  1. A Maytag Bravos washer stuck on sensing can be due to several issues like a faulty lid switch, damaged water inlet valve, or defective control board.
  2. Simple DIY fixes include resetting the washer, checking if it's leveled, or ensuring the lid is fully closed and locked.
  3. For persistent problems, replacing parts like shift actuator, clutch assembly, or control board might be necessary.

Why is your Maytag Bravos washer stuck on sensing and how can you fix it?

Let's start by understanding the possible reasons why your Maytag Bravos washer may be stuck on the sensing mode. Here are a few basic troubleshooting steps you can take to address the issue:

Has your washer been properly balanced?

One common reason for a Maytag Bravos washer to get stuck on sensing is an imbalance in the load. If the load is not evenly distributed in the drum, the washer may have difficulty sensing the load size and proceeding to the wash cycle. Make sure to check if your washer is properly balanced and adjust the legs if necessary. This simple step can sometimes resolve the issue and allow your washer to move past the sensing mode.

Could it be overloaded?

Another factor to consider is whether you have overloaded your washer. Overloading the washer can put excessive strain on the motor and prevent it from moving to the wash cycle. Try running the washer with a smaller load and see if that helps it progress past the sensing mode.

Is the washer lid completely shut (and locked)?

It may seem obvious, but sometimes the simplest solution is the one we overlook. Check if the washer lid is fully closed and locked. If the lid is not functioning properly or not fully closed, the washer may remain in the sensing mode. Ensure that the lid is securely shut and locked before attempting to run the washer again.

By addressing these basic troubleshooting steps, you may be able to resolve the issue and get your Maytag Bravos washer to proceed past the sensing mode. However, if the problem persists, don't worry. There are further troubleshooting methods you can try.

Further troubleshooting methods for a Maytag bravos washer stuck on sensing

If your Maytag Bravos washer is still stuck on sensing after trying the basic troubleshooting steps, it's time to explore additional troubleshooting methods. Here are a few options you can consider:

Have you attempted to reset your washer?

Resetting your washer can sometimes resolve minor issues and get it back on track. To manually reset your Maytag Bravos washer, try these steps:

  1. Unplug the washer from the power source.
  2. Leave it unplugged for about 5 minutes.
  3. Plug the washer back in.
  4. Try running a cycle to see if it progresses past the sensing mode.

If a simple reset doesn't work, there may be a specific component causing the issue. Let's explore a few possibilities:

Consider replacing the shift actuator

The shift actuator is responsible for shifting the washer from the sensing mode to the wash cycle. If the shift actuator is faulty, it may cause your Maytag Bravos washer to get stuck on sensing. In this case, replacing the shift actuator can often resolve the issue. Consult your washer's manual or contact a professional for guidance on how to replace the shift actuator.

Think about changing the clutch and rotor

The clutch and rotor are essential components in the operation of your Maytag Bravos washer. If the clutch is not working properly, it can prevent the washer from transitioning out of the sensing mode. Consider replacing the clutch and rotor if you suspect they may be the cause of the issue.

Making use of the diagnostic mode – the ultimate troubleshooting step

If all else fails, utilizing the diagnostic mode on your Maytag Bravos washer can provide valuable information about any errors or faults. By entering the diagnostic mode, you can run automated tests that can help identify the specific issue causing your washer to get stuck on sensing. Different error codes may indicate problems with components such as the lid lock or the shifter.

To enter the diagnostic mode on your Maytag Bravos washer, follow these steps:

  1. Make sure the washer is plugged in and turned off.
  2. Turn the cycle selector knob to the 3 o'clock position.
  3. Rotate the knob counterclockwise one complete turn.
  4. Rotate the knob clockwise one click and then counterclockwise two clicks.
  5. Rotate the knob clockwise one click.
  6. Press and hold the Start/Pause button for 5 seconds.

Once you've entered the diagnostic mode, follow the instructions provided in your washer's manual or consult a professional to interpret the error codes and take appropriate action.

Wrap Up

Dealing with a Maytag Bravos washer stuck on sensing can be frustrating, but by following the steps outlined in this article, you can troubleshoot and resolve the issue. Start with the basics, such as ensuring proper balance, avoiding overloading, and checking the lid. If the problem persists, try resetting the washer or consider replacing components like the shift actuator or the clutch and rotor. And if all else fails, utilize the diagnostic mode to identify any specific faults or errors.

Remember, if you're unsure about any troubleshooting steps or if the issue persists, it's always a good idea to consult the user manual or contact a professional for assistance. Don't let a stuck sensing mode stop you from enjoying the convenience of your Maytag Bravos washer.

FAQ

How do I manually reset my Maytag Bravos washer?

To manually reset your Maytag Bravos washer, follow these steps:

  1. Unplug the washer from the power source.
  2. Leave it unplugged for about 5 minutes.
  3. Plug the washer back in.
  4. Try running a cycle to see if it progresses past the sensing mode.

Why is my washer stuck on sensing?

There can be several reasons why your Maytag Bravos washer is stuck on sensing. Some possible causes include an unbalanced load, overloading the washer, or a faulty shift actuator. By addressing these issues and following the troubleshooting steps outlined in this article, you can resolve the problem.

What does sensing mean on a Maytag washer?

When a Maytag washer says "sensing," it means that the washer is filling, sensing, and estimating the load size before starting the wash cycle. This mode allows the washer to determine the appropriate water level for the load.

Why is my Maytag washer flashing sense done and lid lock?

If your Maytag washer is flashing "sense done" and "lid lock," it may indicate a problem with the lid lock mechanism. The washer may not be able to progress past the sensing mode if the lid lock is not functioning properly. Try checking the lid lock and ensuring that it is securely closed and locked.

0 0 votes
Article Rating
Subscribe
Notify of
guest
0 Comments
Inline Feedbacks
View all comments